Standing waves are an important issue when looking at feeders / transmission lines, and the standing wave ratio or more commonly the voltage standing wave ratio, VSWR is as a measurement of the level of standing waves on a feeder.
Standing waves represent power that is not accepted by the load and reflected back along the transmission line or feeder.
Although standing waves and VSWR are very important, often the VSWR theory and calculations can mask a view of what is actually happening. Fortunately, it is possible to gain a good view of the topic, without delving too deeply into VSWR theory.
Impedance mismatches in a radio-frequency (RF) electrical transmission line cause reflection of rf power and thus power loss. VSWR is a way to measure transmission line imperfections.
VSWR stands for Voltage Standing Wave Ratio, and is also referred to as Standing Wave Ratio (SWR). It is a measure of how efficiently RF power is transmitted from the power source, through the transmission line, and into the load. Maximum power transfer between two system components occurs when their respective impedances are matched. If the impedances are not identical, some RF power will be reflected back, resulting in a reduction in the amount of power delivered to the load. These reflections cause voltage standing waves. VSWR is defined as the ratio of the maximum voltage to the minimum voltage in the standing wave. The larger the impedance mismatch, the larger the amplitude of the standing wave.
As seen from the above image, red color wave is the reflection from the load.
A common example is a BTS output port connected through a transmission line to an antenna. Suppose If there is no mismatch between the BTS output port and antenna port, then there will not be any reflections and thus VSWR will be equal to 1. And if there is mismatch between BTS output port and antenna port, then VSWR value will be greater than 1 depending upon the amount of mismatch.
Although the concept of VSWR is easy to comprehend, it is extremely difficult to measure directly. For that reason, you need to measure other parameters, such as return loss or reflection coefficient which can then be used to calculate VSWR.
Return loss (RL) is the difference in power (expressed in dB) between the incident power and the power reflected back by the load due to a mismatch.
Return loss (RL) = -10log(Preflected /Pincident )
Once the Return Loss is known, the next step is calculate reflection coefficient ( Γ ),
RL = -20 * Log (Γ )
Γ = 10 (-RL/20)
VSWR can then be calculated using the following formula:
VSWR = (1 + Γ ) / (1 – Γ)
Below is the VSWR table for reference:
Standing waves represent power that is not accepted by the load and reflected back along the transmission line or feeder.
Although standing waves and VSWR are very important, often the VSWR theory and calculations can mask a view of what is actually happening. Fortunately, it is possible to gain a good view of the topic, without delving too deeply into VSWR theory.
Impedance mismatches in a radio-frequency (RF) electrical transmission line cause reflection of rf power and thus power loss. VSWR is a way to measure transmission line imperfections.
VSWR stands for Voltage Standing Wave Ratio, and is also referred to as Standing Wave Ratio (SWR). It is a measure of how efficiently RF power is transmitted from the power source, through the transmission line, and into the load. Maximum power transfer between two system components occurs when their respective impedances are matched. If the impedances are not identical, some RF power will be reflected back, resulting in a reduction in the amount of power delivered to the load. These reflections cause voltage standing waves. VSWR is defined as the ratio of the maximum voltage to the minimum voltage in the standing wave. The larger the impedance mismatch, the larger the amplitude of the standing wave.
As seen from the above image, red color wave is the reflection from the load.
A common example is a BTS output port connected through a transmission line to an antenna. Suppose If there is no mismatch between the BTS output port and antenna port, then there will not be any reflections and thus VSWR will be equal to 1. And if there is mismatch between BTS output port and antenna port, then VSWR value will be greater than 1 depending upon the amount of mismatch.
Although the concept of VSWR is easy to comprehend, it is extremely difficult to measure directly. For that reason, you need to measure other parameters, such as return loss or reflection coefficient which can then be used to calculate VSWR.
Return loss (RL) is the difference in power (expressed in dB) between the incident power and the power reflected back by the load due to a mismatch.
Return loss (RL) = -10log(Preflected /Pincident )
Once the Return Loss is known, the next step is calculate reflection coefficient ( Γ ),
RL = -20 * Log (Γ )
Γ = 10 (-RL/20)
VSWR can then be calculated using the following formula:
VSWR = (1 + Γ ) / (1 – Γ)
Below is the VSWR table for reference:
Post a Comment